View LB080WV3-A1_7831449.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specifications 1/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. c.s. kyeong /g.manager title 8.0?w (800 x rgb x 480) tft - lcd buyer model signature date / / / product engineering dept. lg. philips lcd co., ltd approved by date reviewed by prepared by j.d. kim /manager s.g. kim /engineer a1 suffix lb080wv3 model lg.philips lcd co., ltd. supplier specification for approval ( ? ) preliminary specification ( ) final specification .com .com .com .com 4 .com u datasheet
product specifications 2/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. contents 6 absolute maximum ratings 4 7 electrical specifications 5 3 record of revisions 0 21 precautions 11 20 packing 10 19 international standards 9 18 reliability test 8 15 mechanical characteristics 7 12 electro-optical characteristics 6 5 general specifications 3 4 features 2 4 summary 1 page item no. .com .com .com .com .com 4 .com u datasheet
product specifications 3/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. measuring conditions update : pattern generator & cvbs format add 12 conducting tape shape change on fpc (details compare with ver 0.3) 17 conducting tape width increase (?l? bending type), cover bottom screw one point add(4points ? 5points) & small holes on cover bottom position change because emi characteristic improve. 17 apr.19.2005 0.5 note2 condition change : ?vidoe- = 0 ? ? ?this is cvbs standard format when system output impedance is 75 ? ? 9 cvbs timing diagram change because cvbs level value change ( refer page 8) 9 unify the name : power_on/off ? display enable 9,11 add note ?meets gmw3097(rev4) load dump spec? 6 mar.16.2005 0.4 cvbs amplitude & sync level values change for ntsc & pal standard format 8 mechanical drawing update 16,17 misprinted character correction : y axis, down ( ? 30) because minimum value was misprinted equally to typical value. 12 photo detector change pr-705 ? pr-650 12 misprinted characters -------------------------------------------------------------------------- [ correction ] - may.04.2004 0.1 contents page change 2 july.18.2004 0.2 block diagram change 4 power consumption change : 9.2w(typ) ? 8.84w(typ) 5 psychrometric chart add 6 electrical characteristics parameter add & change 8 cvbs timing diagram add 9 micom reset point change in the power supply input sequence diagram 11 first draft (preliminary) - apr. 27, 2004 0.0 gy (green color coordinates) values change : typ 0.575 ? 0.565 12 display mode description change : reserved ? display version 10 cvbs timing diagram change 9 electrical characteristics timing parameter change 8 aug.24.2004 0.3 summary page revision date revision no. record of revisions .com .com .com .com .com 4 .com u datasheet
product specifications 4/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 1. summary this module utilizes amorphous silicon thin film tr ansistors and a aspect ratio of 16:9. the 8.0? active matrix liquid crystal display allows 262,144 colors to be displayed by analog-to-digital conversion of composite video signal input. the applications are not only rse(rear seat entertainment) for a vehicle, but also display for car navigation system, multimedia applications and other av systems. 2. features ? applying a panel with aspect ratio of 16:9, which makes the module suitable for use in wide-screen systems such as dvd player. ? the 8.0? screen produces a high resolution image that is composed of 384,000 rgb pixel elements in a stripe arrangement. ? technology of wide viewing angle is employed. ? by adopting an active matrix drive, high contrast picture or image is realized. ? by using of cog mounting technology, the module became thin, light and compact. 8.0?w tft-lcd (800xrgbx480) source drive ic gate drive ic backlight unit timing controller gamma reference voltage inverter analog decoder, scaler, adc dc/dc (8) video+ (1) mode control (3) battery+ (2) brightness control digital 6bit r,g,b source control signal gate control signal [ high voltage ] (7) video- (4) gnd (5) brightness control impedance selection (6) display enable b/l control 2wires serial bus r,g,b & sync. gamma reference control board tft-lcd lcd power control power protection & sensing impedance matching & protection impedance matching & protection sensing voltage impedance matching & protection micom main power control .com .com .com .com .com 4 .com u datasheet
product specifications 5/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 3. general specification normal(4:3), full(16:9), zoom(vertical) display modes 800(h) x 3(r,g,b) x 480(v), bgr vertical stripes pixel format 8.0? (20.27 y ), 176.64mm (h) x 99.36mm (v) active screen size (diagonal) 8.84 watts (typ.) power consumption (with ccfl) composite video (except secam) input signal(video) 0.2208 mm ? 0.2070 mm pixel pitch anti-glare treatment surface treatment 1 ccfl (l type) backlight 420g (max.) weight 400 cd/m 2 (typ.) luminance, white 12 o?clock [direction] main viewing direction 198mm (h) x 117mm (v) x 16.0mm (t) (typ.) outline dimension normally white, transmitting mode a-si tft active matrix display technology specification characteristic items .com .com .com .com .com 4 .com u datasheet
product specifications 6/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 4. absolute maximum rating vp-p 1.5 - input impedance 75 ? video+ cvbs ambient surface of panel 2,3 ? 85 -30 - t p operating temperature 2 ? 85 -40 - t st storage temperature 2,3,4 ? 70 -30 - ta 1 vdc 22.0 -0.3 t a =25 ? vbat power supply voltage notes unit max. min. condition symbol parameter notes : 1. meets gmw3097(rev4) load dump spec. 2. maximum wet-bulb temperature is 58 ? . condensation of dew must be avoided, because it may cause electrical current leakage, and deterioration of performance and quality. 3. the operating temperature means that lcd module guarantees operation of the circuit. all the contents of electro-optical specifications are guaranteed under the room temperature condition. 4. this temperature is ambient temperature with regard to the heat which is generated under operation of circuit and backlight on.(reference value) the followings are maximum values which, if exceede d, may cause malfunction or damage to the module. <4upsbhf> <0qfsbujpo> %sz#vmc5fnqfsbuvsf<?> 8fu#vmc 5fnqfsbuvsf<?> ) v n j e j u z <
3 ) > .com .com .com .com .com 4 .com u datasheet
product specifications 7/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 5-1. interface (input terminal) this lcd uses an 8 pin connector , which is used for the module operation, as an interface connection. the model name is ip254-l08b-c51 manufactured by uju electronics. the matching connector is a model cd-104257 manufactured by amp. sec. 5-4 sec. 5-3 notes i i i i i i i i i/o composite video signal ground display enable signal - display enable : v de = vbat - display disable : v de = hi-z(float) (lcd module internally pull-down) impedance selection of brightness control input signal line for single or dual display - hi-z(floating) : for single display - ground : for dual display brightness control composite video signal(cvbs) video+ 8 video- 7 display enable 6 brightness control impedance selection 5 power ground gnd 4 power supply battery+ 3 brightness control 2 display mode control mode control 1 description pin name pin no. 5. electrical specifications .com .com .com .com .com 4 .com u datasheet
product specifications 8/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 5-2. electrical characteristics @t a =25 sync amplitude sync amplitude 2 vp-p 1.5 1.0 0.7 v ntsc ntsc 2 vp-p 0.43 0.285 0.19 v nsync v dc 16.0 13.2 9.0 v de display enable input voltage max. symbol 2 vp-p 0.45 0.3 0.21 v psync notes unit parameter pal horizontal timing ntsc horizontal timing 9 f hp frequency 8 f hn frequency sync width sync width sync width sync width pal vertical timing 9 us t whp 8 us t whn 6,7 v dc 5.5 5.0 4.5 v pwmh high level pwm control signal v dc 1.2 - - v pwml low level 6 hz 220 200 180 f pwm frequency 6,7 - - duty cycle 8 us ) ) ) t wvn 3 mw 3.3 1.45 0.66 p c stand-by power consumption 4 watts 0.924 0.528 0.330 p c b/l off 5 watts 10.16 8.84 7.52 p c normal 4 ma 70 40 25 ibat b/l off 9 ~ f vp frequency 2 vp-p 1.5 1.0 0.7 v pal pal composite video signal 9 us ) ) ) t wvp ntsc vertical timing 1 v dc 16.0 13.2 9.0 vbat power supply input voltage ( battery+ ) frequency normal stand-by 3 ma 0.25 0.11 0.05 ibat 8 ~ f vn lamp life time 10 hours - 5 ma 770 670 570 ibat power supply input current values typ. min. recommended operating conditions .com .com .com .com .com 4 .com u datasheet
product specifications 9/ 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. notes : 1. if the power supply voltage exceeds this range, a lcd module is turned off to avoid serious damage of its circuit components by force. 2. condition :this is cvbs standard format when system output impedance is 75 ? . 3. condition : vbat = 13.2v, display enable(v de ) = hi-z(float) 4. condition : vbat = 13.2v, display enable(v de ) = vbat, mode control signal high duty > 87% 5. condition : vbat = 13.2v, display enable(v de ) = vbat, display image : full black @default brightness, measure time : at least after 10 minutes from the display enable 6. display mode control signal, brightness control signal 7. refer to the section 5-3 and 5-4. 8. ntsc-m, ntsc-j, ntsc-4.43, pal-m, pal-60 9. pal-b,d,g,h,i, pal-n 10. ?lamp life time? is defined as the time the lamp brightness decreases to 50% from initial brightness under continuous lighting condition, at ambient temperature 25 ? . 5-2-1. cvbs standard timing diagram ?)[ g 7/
?)[ g 71
3 ? 1 h(t wvn ) 2.5 ? 1 h(t wvp ) [vertical timing ] ?l)[ g )/
?l)[ g )1
4.7 ? 0.7 us(t whn ) 4.7 ? 0.2 us(t whp ) v ntsc v pal [horizontal timing ] v nsync v psync [ white level ] [ black level ] .com .com .com .com .com 4 .com u datasheet
product specifications 10 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 5-3. display modes control 4,5 backlight off 87 ? duty ? 100 3,5 display version 75 ? duty ? 85 pal 60 zoom 62 ? duty ? 72 pal 60 normal 50 ? duty ? 60 2,5 pal 60 full 37 ? duty ? 47 zoom 25 ? duty ? 35 normal 12 ? duty ? 22 1,5 full 0 ? duty ? 10 notes display mode duty cycle(%) ? protection function when the display mode control terminal is open circuit, short to vbat or short to ground, the default mode becomes full mode. notes : 1. in these modes, the inputted video signal form at is automatically detected.(except secam) 2. these modes are only for pal60 video format. for pal60 format, it is recommended to use these modes. 3. in this mode, micom firmware vers ion of a tft-lcd is displayed on screen. 4. in this mode, backlight and lcd is turned off, but the micom operated. 5. in all of the duty cycle percentage except above each range(for example, 11%, 23%, etc.), the display mode does not change and pr eserve the previous display mode. ? display modes ex.) @ video source format : 4:3 the required range of pwm frequency is 200hz ? 10%. to prevent abnormal display, this pwm frequency should be kept. [ normal mode ] [ full mode ] [ zoom mode ] .com .com .com .com .com 4 .com u datasheet
product specifications 11 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 5-4. brightness mode control 3 screen mute 90 # duty ? 100 2 40 steps, 2% per step - 10% : max. brightness - 90% : min. brightness 10 ? duty ? 90 1 default brightness 0 ? duty # 10 notes brightness mode duty cycle(%) ? protection function when the brightness control terminal is open circuit, short to vbat or short to ground, the brightness becomes default brightness. notes : 1. the default brightness means visually optimal brig htness. all electro-optical characteristics are defined under the default brightness mode. ( if the total brightness steps are 20 levels, default brightness is 10 th step.) 2. because these steps have hysteresis characteri stics, the duty percentage should be changed at least ? 2% to decrease/increase one brightness step. if the duty ? 1% changed, the brightness mode preserve the previous brightness mode. 3. the screen mute means that backlight is turned on and black image is displayed on panel screen. the brightness is controlled by r,g,b gain in the video decoder, not by backlight brightness control. the required range of pwm frequency is 200hz ? 10%. to prevent abnormal display, this pwm frequency should be kept. 5-5. power supply input sequence this power input sequence should be kept to avoid abnormal image and to be an optimum operation. display on : vbat ? video signal ? v de = vbat display off : v de = hi-z(float) ? video signal ? vbat display stand-by : v de = hi-z(float), under the vbat is applied. power input supply (vbat) video signal display enable ( v de ) off hi-z stand-by on stand-by off micom reset .com .com .com .com .com 4 .com u datasheet
product specifications 12 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 6. electro-optical characteristics @t a =25, default brightness mode measuring conditions : -surroundings : dark room -temperature : t a =25 ? -pattern generator : use only st andard analog(cvbs) pattern generator -cvbs format : ntsc-m -electrical parameters set typical values. -measured value at the center point of lcd panel after more than 30 minutes while backlight turning on. tbd (0.379) (0.349) (0.319) r y tbd (0.671) (0.641) (0.611) r x red tbd (0.595) (0.565) (0.535) g y tbd (0.333) (0.303) (0.273) g x green tbd (0.136) (0.106) (0.076) b y tbd (0.175) (0.145) (0.115) b x blue 5 viewing angle 2 color coordinates 4 response time 0.343 0.313 0.283 w x white y axis, down ( t r degree - 60 55 t l degree - 50 45 t u degree - 40 30 t d 0.359 0.329 0.299 w y decay time rise time ms 50 40 - tr d 3 1.40 1.25 - ? center lcd module optical stage(x,y) ; pr-880(luminance), pr-650(color coordinates) or equivalent 500mm fig. 1 optical characteristic measurement equipment and method .com .com .com .com .com 4 .com u datasheet
product specifications 13 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. note) 1. contrast ratio(cr) is defined mathematically as surface luminance with all white pixels contrast ratio = surface luminance with all black pixels 2. surface luminance is measured at the center point(l 1 ) of the lcd with all pixels displaying white at the distance of 50cm by pr-880. color coordinates are measured at the center point(l 1 ) of the lcd with all pixels displaying red, green, blue and white at the distance of 50cm by pr-650. for more information, refer to the fig 1 and fig 2. 3. the variation in surface luminance. the panel total variation ( .com .com .com .com .com 4 .com u datasheet
product specifications 14 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. fig. 3 response time the response time is defined as the following figure and shall be measured by switching the input signal for ?black? and ?white?. tr r tr d 100 90 10 0 % optical response white black white fig. 4 viewing angle z y eye f q .com .com .com .com .com 4 .com u datasheet
product specifications 15 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 7. mechanical characteristics the contents provide general mechanical characteristics for this module. in addition the figures in the next page are detailed mechanical drawing of the lcd. 420g max. weight 99.36 mm vertical 103.8 ( .com .com .com .com .com 4 .com u datasheet
product specifications 16 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. note) unit:[mm], general tolerance: .com .com .com .com .com 4 .com u datasheet
product specifications 17 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. note) unit:[mm], general tolerance: .com .com .com .com .com 4 .com u datasheet
product specifications 18 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 8. reliability test -40 ? (0.5h) ~ 85 ? (0.5h) / 100 cycles (no operation) - 10hz to 200hz logarithm sweep for 15min/cycle. - 10hz to 25hz:the amplitude is 2 mm. - 25hz to 200hz:the acceleration is 2g. - x,z : 8 cycle, y : 16 cycle half sine wave, 80g, 11ms 3 times shock of each six faces -panel surface/top_case : 150 ? , 150pf, ? 15kv (direct discharge, five times) -input terminal : 0 ? , 100pf, ? 200v tp=60 ? 90%rh 240h ta=-30 ? 240h tp=85 ? 240h ta=-40 ? 240h ta=85 ? 240h test condition notes high temperature and high humidity operation test 5 thermal shock test 9 vibration test (non-operating) 8 shock test (non-operating) 7 electro static discharge test 6 low temperature operation test 4 high temperature operation test 3 low temperature storage test 2 high temperature storage test 1 test items no. ? ta ; ambient temperature, tp ; panel surface temperature .com .com .com .com .com 4 .com u datasheet
product specifications 19 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 9. international standards 9-1. safety a) ul 60950, third edition, underwriters laboratories, inc., dated dec. 11, 2000. standard for safety of information technology equi pment, including electrical business equipment. b) can/csa c22.2, no. 60950, third edition, canadian standards association, dec. 1, 2000. standard for safety of information technology equi pment, including electrical business equipment. c) en 60950 : 2000, third edition iec 60950 : 1999, third edition european committee for electro-technical standardization(cenelec) european standard for safety of information technology equipment including electrical business equipment. .com .com .com .com .com 4 .com u datasheet
product specifications 20 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 10. packing 10-1. designation of lot mark 10-2. packing form a) package quantity in one box : 14 pcs b) box size : 329 x 278 x 271 (mm) a) lot mark abcdefghi jklm a,b,c : size(inch) d : year e : month f : panel code g : factory code h : assembly code i,j,k,l,m : serial no. note 1. year b) location of lot mark 2. month the serial no. is printed on the label. the label is attached to the backside of the lcd module. this is subject to change without prior notice. 5. serial no. mark year 6 2006 2 2002 3 2003 4 2004 5 2005 0 2000 1 2001 7 9 8 7 2007 99 98 97 b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 3 2 1 dec mar feb jan a0001 ~ a9999, ..... , z9999 00001 ~ 99999 mark 100000 ~ 1 ~ 99999 year 4. factory code c lpl nanjing mark factory code d k heesung lpl gumi 3. panel code 5 p5 factory 4 p4 factory 3 p3 factory h hydis panel 2 p2 factory mark panel code 1 p1 factory .com .com .com .com .com 4 .com u datasheet
product specifications 21 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. 11. precautions please pay attention to the following when you use this tft lcd module. 11-1. mounting precautions (1) you must mount a module using holes arranged in four corners or four sides. (2) you should consider the mounting structure so that uneven force(ex. twisted stress) is not applied to the module. and the case on which a module is mounted should have sufficient strength so that external forces are not transmitted directly to the module. (3) please attach a transparent protective plate to the surface in order to protect the polarizer. transparent protective plate should have sufficient strength in order to the resist external forces. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothes with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics deteriorate the polarizer.) (7) when the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with a small amount of ethanol. (8) wipe off saliva or water drops as soon as possible. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. (10) the metal case of a module should be contacted to electrical ground of your system. 11-2. operating precautions (1) the spike noise causes the malfunction of circuits. it should be lower than following voltage : v= ? 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lower temperature, it becomes longer.) (3) brightness depends on the temperature. (in lower temperature, it becomes lower.) and in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) be careful for condensation at sudden temperature change. condensation makes damage to polarizer or electrically contacted parts. and after fading condensation, smear or spot will occur. (5) when fixed patterns are displayed for a l ong time, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shall be done by system manufacturers. grounding and shielding methods may be important to minimize the interference. .com .com .com .com .com 4 .com u datasheet
product specifications 22 / 22 lb080wv3 liquid crystal display preliminary ver. 0.5 mar. 16, 2005 note : this document is preliminary version. the latest vers ion must be checked from lg.philips lcd before detail design. since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make certain that handling persons are connected to ground through wris t band etc. and don?t touch interface pin directly. 11-3. electrostatic discharge control strong light exposure causes degradation of polarizer and color filter. 11-4. precautions for strong light exposure when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the module to sunlight or fluorescent light. keep the temperature between 5 ? c and 35 ? c at normal humidity. (2) the polarizer surface should not come in contact with any other object. it is recommended that they be stored in the container in which they were shipped. 11-5. storage (1) when the protection film is peeled off, static electricity is generated between the film and polarizer. this should be peeled off slowly(more than 3 seconds) and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) the protection film is attached to the polarizer with a small amount of glue. if some stress is applied to rub the protection film against the polarizer during the time you peel off the film, the glue is apt to remain on the polarizer. please carefully peel off the protection film without rubbing it against the polarizer. (3) when the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarize r after the protection film is peeled off. (4) you can remove the glue easily. when the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with a small amount of ethanol. 11-6. handling precautions for protection film .com .com .com .com 4 .com u datasheet

▲Up To Search▲

Price & Availability of LB080WV3-A1

	To Download LB080WV3-A1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .